Replacing a failed Disk on a storage spaces direct pool failed

So yesterday i had to replace a disk on a failed HDD in one of our S2D cluster. After replacing the drive and removing the failed drive from the cluster i ran Get-Physicaldisk and noticed i had no disks with Canpool = True. This is normal as S2D will detect the new disk and add it to the Storage Pool to balance the pool correctly.

Read more

DPM 2016 Database Bug

Hello All

Update this is a Windows Defender issue not a database issue.

This will be short, There seams to be a bug in the DPM 2016 database once it reaches a certain size or number of recovery points. We have 2 setup around the same time and both failed within 2 days of each other. The symptoms where backups just standing still not doing anything and if i open resource monitor of perfmonitor it would be slow and sluggish.

Read more

RoCE/RDMA/DCB what is it and how to configure it

Updated May 26th 2018 with HPE FlexFabric config

You have probably heard these acronyms somewhere, so what are these and are they the same. In short yes and no

RoCE stands for RDMA over Converged Ethernet, the RDMA part is Remote Direct Memory Access.

RDMA allows for network data(TCP packets) to be offloaded on the Network cards and put directly in to the memory, bypassing the hosts CPU. Allowing for the host to have all the access to the CPU. In normal TCP offload all the network traffic goes trough the CPU and with higher speeds will take more CPU. On a 10gbit network it would take about 100% cpu on a 12 core Intel Xeon V4 CPU. Read more

Enable DCB on Dell N4000 and Dell Force10 S6000-on

In my plans for our Dataon S2D-3212 setup i had plans on using our Dell N4000 switches for DCB/RDMA, as we have this in both our datacenters. When i did our first install i had problems when enabling DCB with no-drop on the N4000. The N4000 was running firmware version and we where loosing connectivity to some servers when no-drop was enabled. So we ended up buying some new Dell Force10 S6000-on switches, as the Nic’s in our servers are Mellanox ConnectX-4 40Gbit cards. Read more

Storage Spaces Direct Monitoring with Dataon Must

Hi everyone

Last week Dataon officially released there monitoring system for there S2D offering. Dataon Must, it is at the time the only S2D monitoring software out there. There is management packs you can add to SCOM to get alerts and stuff in there. There is also one made for MOMS. Take a look at Stanislavs post about it here. Other then that there is nothing else.

This post will be all about the pictures and not so much about the writing 🙂

Dataon Must is only available with Dataon S2D hardware. As of what i know, it will not be available with non Dataon S2D clusters. When you get this solution it’s delivered as a finished setup. You get a vhdx file to import as a virtual machine. Import it, give it 4gb of ram and min 2 cpu and you are good to go. It’s a Win 2016 server and running a IIS website. Setting it up is quite simple and is done in minutes.

Read more

Dataon S2D-3212 HyperConverged Cluster

Updated 27. feb

We have been testing Storage Spaces Direct for a while on our Ebay cluster. We have been running development and some production systems. As the 2nd exchange node, a mediation server and our vmm server.

We have been looking to replace our current Hyper-V solution that consist of HP BL465c G8 and  BL490 G7 blade servers attached to HP P2000 G3 MSA over iscsi. This has been slower and slower as we have setup more virtual machines. This was a 12 disk shelf with 11 disks active with one spare. One 15k disk gives about 170 iops, giving a whopping 1870 iops on max speed. On normal load it would use about 1200-1500  IOPS so not a lot of spare IOPS. We had one pr cluster.

Most of you know what S2D(Storage Spaces Direct) is, if you don’t go look at Cosmos Darwin’s post over at Technet to get some good insight about S2D.

What i am going to focus on in this blog is the new Dataon HyperConverged server. Back at Ignite 2016  Dataon released there first offering the S2D-3110 all flash solution pumping out 2.6 Million IOPS in a 1u form factor. Read more

Setup VPN to use MFA with NPS Extension

In this blog post i will show you how to setup a Microsoft VPN connection with the new NPS Extension for Azure AD MFA.

This is new service that the Microsoft NPS team just released, that adds an Extension to the Windows Network Policy Server.

When using the NPS extension for Azure MFA, the authentication flow includes the following components:

This is copied from

  1. NAS/VPN Server receives requests from VPN clients and converts them into RADIUS requests to NPS servers.
  2. NPS Server connects to Active Directory to perform the primary authentication for the RADIUS requests and, upon success, passes the request to any installed extensions.
  3. NPS Extension triggers a request to Azure MFA for the secondary authentication. Once the extension receives the response, and if the MFA challenge succeeds, it completes the authentication request by providing the NPS server with security tokens that include an MFA claim, issued by Azure STS.
  4. Azure MFA communicates with Azure Active Directory to retrieve the user’s details and performs the secondary authentication using a verification method configured to the user.

The following diagram illustrates this high-level authentication request flow:

Authentication flow diagram

Read more